Japanese Custom Knives by Takeshi Saji: Unique Blades for Sale

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Origin: Withdrawn from a private collection, previously purchased.
* Condition: Overall in very good condition
* Commercially available: Discontinued
* Sharpening: Factory sharpened
* Marks on blade: None
* Marks on handle: A few small marks on steel heads.
* Box: Present
* Scabbard: Present
* Manuals, Certificates and Warranties: /
* Checked and Certified by our in-house laboratory

Intended Use: Collection / Gentleman

Type of Production: Semi-Industrial
Country of Production: Japan
Blade: Stainless steel AUS6
Blade treatment: Satin finish
Handle: Mother of pearl and stainless steel heads
Blade length: 40mm.
Blade thickness: 2mm.
Length closed: 55mm.
Total length: 97mm.
Weight: 14g.
Closure: Back Lock
Sheath: small blue velvet case with Al-Mar Knives logos
Packaging: cardboard box with Al-Mar Knives logos.
Notes: very rare knife produced in the 1980s withdrawn from private collection

Charming knife used by the Japanese farmer.

As is typical for many agricultural tools, this Japanese knife is also extremely simple but the result of a centuries-old improvement that has found the difficult balance between form and function, and between cost and benefit.

The main feature is certainly the quality of the blade, in fact it uses a three-layer San Mai steel, of which the very hard one in the center.

It has a razor wire, as befits a tool created to cut and not just to be displayed in display cases.

Blade: San Mai carbon steel - Yasuki Steel Blue Paper Steel 62hrc in clad
Handle: iron foil
Closing: without blade lock
Length closed: 92mm.
Blade length: 76mm.
Blade thickness: 2.7mm
Open length: 155mm
Weight: 33g.
Note:

Mcusta - Nami Small Damascus Japan - MC-0111D - knife

Collini Cutlery is the official distributor for Italy of Japanese knives Mcusta

Intended Use: Sport / collection

Type of production: industrial cutting - assembly and handcrafted finishes
Blade: Stainless steel sanmai with sharp VG-10 to 59/60HRC cheeks and external nickel damascus 33 layers
Blade Production: Japan
Handle: steel hammered
Blade length: 65mm.
Blade Thickness: 3mm.
Closed Length: 95mm.
Overall length: 160mm.
Balancing: -
Weight: 74g.
Lock: Liner Lock
Clip: -
Sheath: -
Notes: -

KNIFE WITHDRAWN FROM A PRIVATE COLLECTION
* Type: 2016 knife previously purchased and withdrawn from a private collection
* Condition: Like new, never used, never removed from packaging
* Commercial availability: Difficult to find
* Sharpening: Factory edge
* Blade marks: None
* Handle marks: None
* Box: Present and complete, with outer box
* Sheath: -
* Manuals, Certificates, and Warranty: Present and complete
Inspected and Certified by our internal laboratory

SHIN in Japanese means ‘trust’.

The SHIN is one of the largest folders in the Rockstead catalog and showcases all the typical and characteristic elements of the brand: aluminum handle with a pearl-radiant design, hardened anodization at 400 Vickers, and an insert of high-quality stingray leather (Samekawa).

This is a durable knife with strong cutting capabilities that maintains its edge for a long time. Even when used for rigorous cuts, the blade glides securely thanks to its particular sharpening.

The blade indeed has a HONZUKURI sharpening, convex on both sides, following the tradition of Japanese swords; this makes it both very sharp and sturdy, allowing it to cleanly cut a sheet of paper even after 1000 cuts through a very abrasive and resistant hemp rope.

A faithful companion for life, in which to place the utmost trust.

Blade: laminated stainless steel ZDP189 at 67HRC internally and VG10 at 61.7HRC externally
Handle: samekawa (genuine stingray leather) and aerospace-grade aluminum A6063S with black alumite treatment at 400Hv hardness
Blade length: 95mm.
Blade thickness: 4mm.
Total length: 210mm.
Weight: 145g.
Lock: linerlock type, made of 402J2 steel at 50HRC
Clip: removable, made of 402J2 steel at 50HRC, with black alumite treatment at 400Hv
Notes: complete with warranty certificate and technical specifications

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Provenance: withdrawn from a private collection, previously purchased.
* Condition: 2011 specimen, overall in very good condition.
* Commercially available: Still in catalog, but difficult to find.
* Sharpening: Factory.
* Marks on blade: None
* Marks on handle: minimal marks given by time.
* Box: Present
* Scabbard: Present
* Manuals, Certificates and Warranties: Present
* Checked and Certified by our in-house laboratory

Intended Use: Collection / Sporting

Production type: Midtech
Country of manufacture: Sakai - Japan
Blade: ZDP189 stainless steel at 66.3 HRC
Blade treatment: mirror polish
Handle: Aluminum A6063S with anodization to Hv400 hardness and genuine Breed leather inserts
Blade length: 82mm.
Blade thickness: 3.7mm.
Length closed: 111mm.
Total length: 189mm.
Thickness when closed: 16.2mm.
Weight: 133g.
Opening: via ambidextrous pin 
Washers: steel
Closure: Sub FrameLock of 2mm. made of SUS402J2 stainless steel at 50HRC
Clip: deep pocket, 1mm. 420J2 stainless steel with PVD treatment
Packaging: wooden box with Rockstead logos, certificate with serial number and steel hardness test
Notes: Specimen number #046 dated 07/13/2011, previously purchased, withdrawn from a private collection

Kanetsune Seki produces traditional, high-quality kitchen spoons, suitable for daily use. These cuchillos are the result of the skill of craftsmen who implement scrupulous techniques. Our quality guarantees products that are exceptionally durable, sharp and of extraordinary beauty.

These cuchillos are destined to continually improve, fusing new ideas with traditional techniques transmitted over more than 800 years. Kitasho Co., Ltd. was founded in 1964 in the city of Seki, Japan, known as "The City of Swords", both nationally and internationally.

We constantly strive to offer short, durable and useful items, renewing our commitment to innovation in keeping with new times.

The range of products includes kitchen spoons, navajas, camping spoons, high-end cooking spoons for even the most refined palates, as well as tigers and shorts, and everyday items.

Intended use: home/collection

Type of artesanal production
Hoja: 33 head sanmai maple with Hitachi Aogami 64HRC carbon wire and 1095 brut de forge carbon maple shells.
Production of Japanese spoons
Mango: en madera de roble
Hoja length: 245 mm.
Hole thickness: 6 mm.
Closed length: -
Total length: 410 mm.
Balance: in the guard branch
Weight: 538g.
Cierre: -
Videos: -
Funda: madera de roble
Package: Black and red cardboard box with Kanetsune logos.
Note:-

Characteristics of San Mai Maple: These are different types of metals combined to create a composition that contains and intensifies the resistance of the metals individually:

- Mayor vida útil del filo
Thanks to the use of very high quality maples with high carbon content (VG10, CoS, Shiro) or sintered (SPG2), in the core of the plate (Core Steel), the heat, once templada, has a hardness and a Decidedly superior court performance. which were achieved with the use of traditional maple trees.

- Mayor resilience
Built according to the principle of Japanese swords, the multi-headed maple is difficult to break thanks to the hardness of the central maple (Core Steel) and the elasticity of the maple used for the lateral covering (Stainless Steel).

- Better resistance to corrosion
The maple used for the external caps (Stainless Maple) guarantees the house a high resistance to corrosion. The combination of the two or more materials used by Takefu Steel generates, at the galvanic level, a structure that improves resistance to corrosion, including in the steel.

- Easy processing including after heat treatment
Although the maple is normally hardened after the tempering, the lateral maple used in the multi-head process does not become softer and allows for easy mechanicalization, cutting or soldering even after the heat treatment. For optimal health performance, cryogenic treatment is recommended.

- Improved aesthetic result
The cuchillos made with multi-layered maple or with damask pattern are aesthetically elegant, refined and much appreciated by collectors around the world at the end of the manufacturing process.

For more information: collinsteel

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Origin: Withdrawn from a private collection, previously purchased.
* Condition: In excellent, like-new condition
* Commercially available: Still in production
* Sharpening: Factory sharpened
* Marks on blade: None
* Marks on handle: None
* Box: Present
* Scabbard: /
* Manuals, Certificates and Warranties: Present
* Checked and Certified by our in-house laboratory

Intended Use: Collection / Sporting

Production type: Midtech
Country of manufacture: Sakai - Japan
Blade: Hitachi YXR7 steel at 64 HRC
Blade treatment: Black Hard Anodized at Hv400 hardness
Handle: Duraluminum A7075 with anodized to Hv400 hardness
Blade length: 70mm.
Blade thickness: 3.3mm.
Length closed: 104mm.
Total length: 176mm.
Thickness when closed: 11.4mm.
Weight: 74g.
Opening: via ambidextrous pin 
Washers: steel
Closure: FrameLock with clapper made of SKD11 at 61HRC
Clip: removable, 1mm 420J2 stainless steel with PVD treatment
Packaging: Wooden box with Rockstead logos, certificate with serial number and steel hardness test
Notes: serial number 338 - Production date 20/03/2019

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Provenance: withdrawn from a private collection, previously purchased.
* Condition: in excellent, like-new condition
* Commercially available: In production
* Sharpening: Factory
* Marks on blade: None
* Marks on handle: None
* Box: Present
* Scabbard: /
* Manuals, Certificates and Warranties: Present
* Checked and Certified by our in-house laboratory

Intended Use: Collection / Sporting

Production type: Midtech
Country of manufacture: Sakai - Japan
Blade: stainless steel ZDP-189 at 66.6 HRC
Blade finish: mirror polish
Handle: Duraluminum A7075 with anodization to Hv400 hardness and Samekawa insert (genuine Breed leather)
Blade length: 95mm.
Blade thickness: 4mm.
Total length: 210mm.
Weight: 145g.
Opening: via ambidextrous pivot 
Washers: steel
Closure: FrameLock with hinge made of 420J2 at 52HRC
Clip: removable, 1mm 420J2 stainless steel with PVD treatment
Packaging: Wooden box with Rockstead logos, certificate with serial number and steel hardness test
Notes: serial number 054 - Date of manufacture 23/04/2019

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Origin: Withdrawn from a private collection, previously purchased.
* Condition: Overall in good condition, some minor abrasion on clip and hardware
* Commercially available: Discontinued
* Sharpening: Factory.
* Marks on blade: None
* Marks on handle: Small abrasions on clip and hardware.
* Box: Present
* Scabbard: /
* Manuals, Certificates and Warranties: Present
* Checked and Certified by our in-house laboratory

Intended Use: Collection / Sporting

Production type: Midtech
Country of manufacture: Sakai - Japan
Blade: Hitachi YXR7 steel at 64.7 HRC
Blade treatment: Black Titanium mirror coat
Handle: Duraluminum A7075 with anodizing to Hv400 hardness
Blade length: 70mm.
Blade thickness: 3.3mm.
Length closed: 104mm.
Total length: 176mm.
Thickness when closed: 11.4mm.
Weight: 74g.
Opening: via ambidextrous pin 
Washers: steel
Closure: FrameLock with clapper made of SKD11 at 61HRC
Clip: removable, 1mm 420J2 stainless steel with PVD treatment
Packaging: Wooden box with Rockstead logos, certificate with serial number and steel hardness test
Notes: serial number 014 - Production date October 9, 2009

Higo is one of the most beloved models for Rockstead Knives fans around the world, and HIGOⅡX, with a custom Dark Matter Gold (DMG) carbon fiber coating and a titanium back layer, is one more step in the pursuit of perfection. The blade is made of ZDP189 super stainless steel and features a unique convexity with gradually reduced angle (30 degrees at the middle and 24 degrees at the tip). The variable blade angle is the result of Rockstead's long quest for superior sharpness and cutting ability.

Blade: ZDP-189 stainless steel at 66.7HRC
Handle: anodized titanium and Dark Matter Gold carbon fiber
Blade length: 89mm.
Blade thickness: 3.2mm.
Total length: 216mm.
Weight: 138g.
Closure: Frame Lock with SKD11 casement at 61HRC
Clip: made of 402J2 steel at 48HRC
Notes: Accompanied by warranty certificate with full technical specifications

With Rockstead brand of Ishida Co. Sakai, Japan, they are currently marketed with the best industrial knives currently in production.

Created by Katsumi Kitano, who for 20 years has been producing quality knives so much to have been awarded the highest award among the knife craftsmen in Japan, you demonstrate exceptional both in cutting capacity, penetration and tightness of the wire both in terms of innovation for and materials used for the construction techniques.

Blade: ZDP189 rolled stainless steel at 66.6 HRC inside and VG10 at 60.8 HRC outside
Handle: Same (real ray skin) and aircraft aluminum with black alumite treatment to HV400
Blade length: 95 mm.
Blade thickness: 4 mm.
Overall length: 210 mm.
Weight: 145 g.
Lock: Liner Lock steel in 52HRC 402J2
Clip: Steel 402J2 to 52HRC
Notes: Accompanied by a certificate of guarantee with the technical specifications.

With the Rockstead brand of Ishida Co. of Sakai, Japan, the best industrial knives currently in production are currently marketed.
Created by Katsumi Kitano, who for over 20 years has been producing quality knives so as to have been awarded the highest recognition among artisan knives in Japan, they are exceptional both in cutting capacity, penetration and hold of the thread and in innovation for the materials used and for construction techniques.

Intended use: Collection / Sports

Type of production: Midtech
Country of production: Sakai - Japan
Blade: in Hitachi YXR7 steel at 64HRC
Blade treatment: Black DLC mirror
Handle: A7075 Duralumin with Hv400 hardness anodizing
Blade length: 70mm.
Blade thickness: 3.3mm.
Length closed: 104mm.
Total length: 176mm.
Thick when closed: 11.4mm.
Weight: 74g.
Opening: through ambidextrous pin
Washers: in steel
Closure: FrameLock with wing in SKD11 at 61HRC
Clip: removable, in 420J2 stainless steel of 1mm. with PVD treatment
Packaging: Wooden box with Rockstead logos, certified with serial number and steel hardness test
Notes: -

Blade: stainless steel ZDP-189 to 67.2HRC
Handle: Duralumin A2024 with anodized surface to HV400
Blade length: 73 mm.
Blade Thickness: 3.5 mm.
Overall length: 176 mm.
Weight: 172 g.
Lock: Frame Lock with a swing in SKD11 61HRC
Clip: Steel 402J2 to 48HRC
Notes: Accompanied by a certificate of guarantee with the technical specifications.

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Type: Previously Purchased
* Condition: In very good condition
* Commercially available Discontinued
* Sharpening: Factory
* Marks on blade: -
* Marks on handle: - -
* Box: marketed in silk pouch.
* Scabbard: Leather, belt, original, with a few small marks given by time.
* Manuals, Certificates and Warranties: present.
* Checked and Certified by our in-house laboratory



The HIGO-MH-DLC folder features a 3.5-inch YXR7 blade with DLC coating and Micarta handle. The incredible mirror finish is achieved by heat treating the blade and gradually grinding by hand with wet and dry sandpaper of 400, 600, 800, 1,200 and 2,000. The HIGO-MH-DLC comes with a black leather belt case with a slot to hold the included torx wrench.

Country of manufacture: Japan
Type of manufacture: midtech
Blade: DLT571 steel (Hitachi YXR7 at 64.1HRC with 3micron HPC coating and hardness of Hv1300)
Handle: 2mm stainless steel sus402J2 at 52HRC with micarta handles
Blade length: 90mm.
Blade thickness: 3.5mm.
Total length: 216mm.
Weight: 139g.
Closure: Liner Lock
Clip: stainless steel
Notes: Serial number 303 - 2010 knife accompanied by warranty certificate with technical specifications - Model discontinued and no longer commercially available

KNIFE WITHDRAWN FROM PRIVATE COLLECTION
* Type: Previously Purchased
* Condition: Like new
* Commercially available Discontinued
* Sharpening: Factory
* Marks on blade: None
* Marks on handle: None
* Box: Present
* Scabbard: -
* Manuals, Certificates and Warranties: Present
* Checked and Certified by our in-house laboratory.


The best industrial knives currently in production are marketed under the Rockstead brand. Created by Katsumi Kitano, who has been making quality knives for more than 20 years to the extent that he has been awarded the highest distinction among artisan knife makers in Japan, they prove to be exceptional both in cutting ability, penetration and edge-holding and in the level of innovation for the materials used and construction techniques.

Country of production: Japan
Type of production: midtech
Blade: Hitachi YXR7 steel at 64.8HRC with 3micron HPC coverage and hardness of Hv1800
Handle: Duralumin A2024 with surface anodizing and hardness of Hv400
Blade length: 90mm.
Blade thickness: 3.5mm.
Total length: 215mm.
Weight: 130g.
Closure: Frame Lock with SKD11 casement at 61HRC
Clip: made of 402J2 steel at 48HRC
Notes: Serial number 005 - 2010 knife accompanied by warranty certificate with technical specifications - Model discontinued and no longer commercially available

Under the brand name Rockstead, from Ishida Co. in Sakai, Japan, the best industrial knives currently in production are currently marketed: created by Katsumi Kitano, who has been making quality knives for over 30 years to the extent that he has been awarded the highest distinction among artisan knife makers in Japan, they prove to be exceptional both in cutting ability, penetration and edge-holding and in innovation in the materials used and construction techniques.

Intended Use: Collection/Sportsman

Type of production: Midtech
Country of manufacture: Sakai - Japan
Blade: rolled stainless steel ZDP189 at 66.4 HRC on the inside and VG10 at 61.3 HRC on the outer cheeks
Blade treatment: mirror polish
Handle: Aluminum A6063S with anodization to Hv400 hardness and genuine Breed leather inserts
Blade length: 82mm.
Blade thickness: 3.7mm.
Length closed: 111mm.
Total length: 189mm.
Thickness when closed: 16.2mm.
Weight: 133g.
Opening: via ambidextrous pin
Washers: steel
Closure: Sub FrameLock of 2mm. made of SUS402J2 stainless steel at 50HRC
Clip: deep pocket, 1mm. 420J2 stainless steel with PVD treatment
Packaging: Wooden box with Rockstead logos, certificate with serial number and steel hardness test
Notes: Shinogi Zukuri type blade sharpening

Extremely limited edition Platinum Label series folding knife with Mokume damascus blade and heads produced in only 20 examples each with a different coloration of the wood briar. Each specimen is therefore unique and differs from the previous one.

Intended use: collection

Type of production: industrial cutting - craftsmanship, assembly and finishing
Country of production: Seki - Japan
Blade: made of Mokume stainless steel with VG-10 cutting edge, forged with rainbow damascus rolling, achieved through layers of stainless steel, copper and brass and hammered through Tsuchime technique
Handle: made of Mokume stainless damask steel and wood briar
Blade length: 80mm.
Blade thickness: 3mm.
Length closed: 110mm.
Total length: 195mm.
Thickness when closed: 14mm.
Weight: 208g.
Closure: Liner Lock
Clip: handcrafted, removable and reversible, hammered stainless steel
Packaging: wooden box with Mcusta logos
Notes: Special and Limited Edition made in only 20 pieces for the Blade Show in Atlanta 2022

Collini Cutlery is the official distributor for Italy of MCUSTA Japanese knives

Intended use: sports / collection

Type of production: industrial cutting - handcrafted assembly and finishing
Blade: SPG2 61 / 62HRC
Blade treatment: -
Production Lama: Japan
Handle: Damascus steel and pakka wood
Blade length: 70mm.
Blade thickness: 3mm.
Closed length: 96mm.
Total length: 166mm.
Balancing: -
Weight: 96g.
Closure: Liner Lock
Clip: -
Sheath: cordura
Note: -

Knife collected from a private collection in like new condition with original box - Knife made in 2017 by the famous Japanese knifemaker Takeshi Saji - The knife is supplied together with the sheath made by Saji, with an additional sheath made by the Italian cutler Simone Tonolli. This second sheath allows horizontal attachment to the belt. Checked and certified by our internal laboratory.

Takeshi Saji was born in 1948 in Takefu (Fukui prefecture), a city located roughly in the center of Japan and in the heart of an area for centuries devoted to the production of blades. His workshop is still there, built around the oven thanks to which, for several years now, Takeshi Saji has been forging steel (especially damascus) with which he makes various models of traditional Japanese knives. The choice of materials for the finishes (mainly natural), the essential lines - evocative of use - and the chromatic combinations of rare impact make his creations unique and unmistakable in the panorama of world cutlery and, at home, they have earned him the prestigious title of Master.

Intended use: Collection / Sports

Type of production: Artisan
Production Lama: Japan
Blade: Hand forged, Yoshoku laminated damask with Hitachi Aogami cutting edge at 64HRC
Blade treatment: -
Handle: Koinobori (carp) and Tou-Maki (rattan)
Blade length: 100mm.
Blade thickness: 4mm.
Closed Length: -
Total length: 207mm.
Thick when closed: -
Balancing: -
Weight: 128g.
Closure: -
Clip: -
Sheath: two leather sheaths, one produced by Takeshi Saji for vertical positioning and one made by the Italian knifemaker Simone Tonolli for horizontal fixing
Packaging: Cardboard box
Notes: entirely handmade by Takeshi Saji

Knife withdrawn from a private collection in excellent condition, uniquely has a small imperfection on the wood at the base of the handle (visible in the close up of the photos) - Complete with original box - Checked and certified by our in-house Coltelleria Collini laboratory.

The SHINRA MAXIMA series uses the sintered and cryogenically hardened Japanese steel SPG2 in 3-layer laminate, one of the best ever produced in Japan

Intended use: sports / collection

Type of production: industrial cutting - handcrafted assembly and finishing
Production Lama: Japan
Blade: 61 / 62HRC SPG-2 stainless steel in three-layer San Mai laminate
Handle: Pakka Wood
Blade length: 95mm.
Blade thickness: 3mm.
Closed length: 115mm.
Total length: 207mm.
Thick when closed: 17.5mm.
Weight: 100g.
Closure: Liner Lock
Clip: in stainless steel
Packaging: cardboard box with Mcusta logos
Note: -

For more information on the steel used, you can visit the website: www.collinisteel.com

Takeshi Saji was born in 1948 in Takefu (Fukui prefecture), a city located roughly in the center of Japan and in the heart of an area for centuries devoted to the production of blades. His workshop is still there, built around the oven thanks to which, for several years now, Takeshi Saji has been forging steel (especially damascus) with which he makes various models of traditional Japanese knives. The choice of materials for the finishes (mainly natural), the essential lines - evocative of use - and the chromatic combinations of rare impact make his creations unique and unmistakable in the panorama of world cutlery and, at home, they have earned him the prestigious title of Master.

Intended use: Collection / Sports / Machete

Type of production: Artisan
Production Lama: Japan
Blade: Hand forged, laminated damask with 64HRC Hitachi Shirogami cutting edge
Blade treatment: -
Handle: Paracord Green
Blade length: 205mm.
Blade thickness: 5mm.
Closed Length: -
Total length: 335mm.
Thick when closed: -
Balancing: -
Weight: 358g.
Closure: -
Clip: -
Sheath: ** LEATHER **
Packaging: Cardboard box
Notes: entirely handmade by Takeshi Saji

Takeshi Saji was born in 1948 in Takefu (Fukui prefecture), a city located roughly in the center of Japan and in the heart of an area for centuries devoted to the production of blades. His workshop is still there, built around the oven thanks to which, for several years now, Takeshi Saji has been forging steel (especially damascus) with which he makes various models of traditional Japanese knives. The choice of materials for the finishes (mainly natural), the essential lines - evocative of use - and the chromatic combinations of rare impact make his creations unique and unmistakable in the panorama of world cutlery and, at home, they have earned him the prestigious title of Maestro.

Intended use: table / sports / collection
Type of production: Artisan
Production Lama: Japan
Blade: Hand forged, laminated damascus with 15-layer SPG2 steel edge
Handle: in black G10
Blade length: 100mm.
Blade thickness: 2.5mm.
Total length: 240mm.
Weight: 80g.
Packaging: Cardboard box and leather sheath
Notes: The knife is handmade by Takeshi Saji

Takeshi Saji was born in 1948 in Takefu (Fukui prefecture), a city located roughly in the center of Japan and in the heart of an area for centuries devoted to the production of blades. His workshop is still there, built around the oven thanks to which, for several years now, Takeshi Saji has been forging steel (especially damascus) with which he makes various models of traditional Japanese knives. The choice of materials for the finishes (mainly natural), the essential lines - evocative of use - and the chromatic combinations of rare impact make his creations unique and unmistakable in the panorama of world cutlery and, at home, they have earned him the prestigious title of Maestro.

Intended use: sports / collection
Type of production: Artisan
Production Lama: Japan
Blade: Hand forged, laminated damascus with 15-layer SPG2 steel edge
Handle: in black G10
Blade length: 110mm.
Blade thickness: 2.5mm.
Total length: 235mm.
Weight: 120g.
Packaging: Cardboard box
Notes: The knife is handmade by Takeshi Saj

Coltelleria Collini is the official distributor for Italy of MCUSTA Japanese knives

Intended use: sports / collection

Type of production: industrial cutting - handcrafted assembly and finishing
Blade: SanMai steel with VG-10 stainless steel edge at 59 / 60HRC and external cheeks in 33-layer nickel damascus
Production Lama: Japan
Handle: Micarta
Blade length: 45mm.
Blade thickness: 3mm.
Closed length: 70mm.
Total length: 118mm.
Balancing: -
Weight: 44g.
Closure: Liner Lock
Clip: in deep pocket steel
Sheath:
Note: -

Multi-purpose vegetable and fruit knife. Thanks to the wooden case (shirasaya), similar to the one used for the katana or the tanto, the blade remains perfectly protected and easily transportable.

Intended use: Sports / Collection

Blade: 420J2 steel
Japan blade production
Handle: cherry wood
Blade length: 105mm.
Blade thickness: 1mm.
Total length: 210mm.
Balancing: -
Weight: 36g.
Sheath: cherry wood sheath
Note:

Retired from rivata collection - Rare Rockstead model produced in 2009 in SANMAI ZDP189 and ATS34 steel - the temper of this piece has reached a rare hardness of 67.4 hrc - Knife in like new condition.

Checked and certified by our internal laboratory - Collini Cutlery.

The best industrial knives currently in production are currently marketed under the Rockstead brand, of Ishida Co. of Sakai, Japan.

Created by Katsumi Kitano, who has been producing quality knives for over 20 years so as to have been awarded the highest recognition among artisan cutlers in Japan, they prove to be exceptional both in cutting capacity, penetration and edge retention and in terms of innovation for materials used and for the construction techniques.

Blade: SanMai ZDP189 and ATS-34 stainless steel at 67.4 HRC
Handle: Same (real stingray leather) and aircraft aluminum with black alumite treatment at Hv400
Blade length: 95 mm.
Blade thickness: 4 mm.
Total length: 210 mm.
Weight: 145 g.
Closure: Liner Lock in 402J2 steel at 52HRC
Clip: 402J2 to 52HRC steel
Notes: Accompanied by a guarantee certificate with technical specifications.

Takefu Knives Village is a brand born in 1991 in Echizen Fukui, a city in Japan famous since 1400 for the production of knives.

The Takefu knives brand is based on the union of 10 local artisans who forge each knife by hand

Characteristics of the knife: Mr. Masanobu Okada

Use: collection / sports

Blade: three-layer clad steel with a 62 / 63HRC Shirogami cutting edge
Lama origin: Japan
Handle: black paracord
Packaging: -
Blade length: 60mm
Total length: 165mm
Blade thickness: 4mm
Production: artisanal
Weight: 79g

Sheath: in kydex handcrafted by Simone Tonolli

Takefu Knives Village is a brand born in 1991 in Echizen Fukui, a city in Japan famous since 1400 for the production of knives.

The Takefu knives brand is based on the union of 10 local artisans who forge each knife by hand

Characteristics of the knife: Mr. Masanobu Okada

Use: collection / sports

Blade: three-layer clad steel with a 62 / 63HRC Shirogami cutting edge
Lama origin: Japan
Handle: black paracord
Packaging: -
Blade length: 75mm
Total length: 190mm
Blade thickness: 4mm
Production: artisanal
Weight: 114g

Sheath: in kydex handcrafted by Simone Tonolli

Takefu Knives Village is a brand born in 1991 in Echizen Fukui, a city in Japan famous since 1400 for the production of knives.

The Takefu knives brand is based on the union of 10 local artisans who forge each knife by hand

Characteristics of the knife: Mr. Masanobu Okada

Use: collection / sports

Blade: three-layer clad steel with a 62 / 63HRC Shirogami cutting edge
Lama origin: Japan
Handle: black paracord
Packaging: -
Blade length: 60mm
Total length: 167mm
Blade thickness: 4mm
Production: artisanal
Weight: 78g

Sheath: in kydex handcrafted by Simone Tonolli

Takefu Knives Village is a brand born in 1991 in Echizen Fukui, a city in Japan famous since 1400 for the production of knives.

The Takefu knives brand is based on the union of 10 local artisans who forge each knife by hand

Characteristics of the knife: Mr. Masanobu Okada

Use: collection / sports

Blade: three-layer clad steel with a 62 / 63HRC Shirogami cutting edge
Lama origin: Japan
Handle: black paracord
Packaging: -
Blade length: 65mm
Total length: 165mm
Blade thickness: 4mm
Production: artisanal
Weight: 83g

Sheath: in kydex handcrafted by Simone Tonolli

Beautiful traditional Japanese sickle handcrafted in laminated steel from Takefu Knives Village. Brand born in 1991 in Echizen Fukui, a city in Japan famous since 1400 for the production of knives.

Kama Features:

Use: collection / gardening

Blade: CladSteel carbon steel with 62 / 64HRC White Paper Steel (Shirogami) cutting edge and 33-layer "Suminagashi" damask
Lama origin: Japanese craftsmanship
Handle: Wood
Packaging: -
Blade length: 195mm
Total length: 430mm
Blade thickness: 3.7mm
Handle length: 360mm
Weight: 264g

The kama is a traditional agricultural tool typical of Japan and Okinawa, similar to a small sickle used to harvest wheat, and also used as a weapon. Before being used in martial arts, kama was used extensively in Asia to cut crops, especially rice.

Extremely limited edition Yatagarasu MCUSTA folding knife of the Shinwa series, with Mokume blade and produced in only 100 pieces.

Yatagarasu, in Japanese culture, is a three-legged crow symbol of driving owned by the Sun goddess Amaterasu. Yatagarasu appears in ancient Japanese documents, such as Kojiki (古 事 記), in which it is also said that he fought and killed a beast intending to devour the Sun, and that he is also the protector of the emperor Jimmu.
On many occasions, in Japanese art this creature is represented with three legs, although in Kojiki it is never said that the Yatagarasu has more than two. Today, the three-legged version of the Yatagarasu is used as a symbol of the football federation of Japan.

Intended use: collection

Type of production: industrial cutting - craftsmanship, assembly and finishes
Lama production: Japan
Blade: stainless steel Mokume Damascus - Aogami (blue steel) forged with lamination of rainbow Damascus, obtained thanks to layers of stainless steel, copper and brass and with black hammering through the Tsuchime technique
Handle: in stainless damask with dark purple corian insert and copper and gold inlays
Blade length: 80mm.
Blade thickness: 3mm.
Length closed: 110mm.
Total length: 195mm.
Thick when closed: 14mm.
Weight: 141g.
Closure: Liner Lock
Clip: -
Packaging: wooden box with Mcusta logos
Notes: limited edition 100 pieces

For more information on the steel used you can view the site: www.collinisteel.com

Collini Cutlery is the official distributor for Italy of the Japanese MCUSTA knives

The SHINRA MAXIMA series uses Japanese sintered and cryogenically hardened SPG2 in 3-layer laminate, one of the best ever produced in Japan

Intended use: sports / collection

Type of production: industrial cut - assembly and handmade finishes
Lama production: Japan
Blade: 61 / 62HRC SPG-2 stainless steel in three-layer San Mai laminate
Handle: Damascus
Blade length: 90mm.
Blade thickness: 3mm.
Length closed: 117mm.
Total length: 211mm.
Thick when closed: 17.5mm.
Weight: 170g.
Closure: Liner Lock
Clip: stainless steel
Packaging: cardboard box with Mcusta logos
Note: -

For more information on the steel used you can view the site: www.collinisteel.com

Collini Cutlery is the official distributor for Italy of the Japanese MCUSTA knives

The SHINRA MAXIMA series uses Japanese sintered and cryogenically hardened SPG2 in 3-layer laminate, one of the best ever produced in Japan

Intended use: sports / collection

Type of production: industrial cut - assembly and handmade finishes
Lama production: Japan
Blade: 61 / 62HRC SPG-2 stainless steel in three-layer San Mai laminate
Handle: Pakka wood
Blade length: 95mm.
Blade thickness: 3mm.
Length closed: 115mm.
Total length: 207mm.
Thick when closed: 17.5mm.
Weight: 100g
Closure: Liner Lock
Clip: stainless steel
Packaging: cardboard box with Mcusta logos
Note: -

For more information on the steel used you can view the site: www.collinisteel.com

Collini Cutlery is the official distributor for Italy of the Japanese MCUSTA knives

The SHINRA MAXIMA series uses Japanese sintered and cryogenically hardened SPG2 in 3-layer laminate, one of the best ever produced in Japan

Intended use: sports / collection

Type of production: industrial cut - assembly and handmade finishes
Lama production: Japan
Blade: 61 / 62HRC SPG-2 stainless steel in three-layer San Mai laminate
Handle: Micarta
Blade length: 90mm.
Blade thickness: 3mm.
Length closed: 117mm.
Total length: 211mm.
Thick when closed: 17.5mm.
Weight: 105g.
Closure: Liner Lock
Clip: stainless steel
Packaging: cardboard box with Mcusta logos
Note: -

For more information on the steel used you can view the site: www.collinisteel.com

Collini Cutlery is the official distributor for Italy of the Japanese MCUSTA knives

Intended use: dirty / collection

Type of production: industrial cut - assembly and handmade finishes
Blade: SPG2 61 / 62HRC
Blade treatment: -
Lama production: Japan
Handle: damask steel and pakka wood
Blade length: 70mm.
Blade thickness: 3mm.
Length closed: 96mm.
Total length: 166mm.
Balancing: -
Weight: 96g.
Closure: Liner Lock
Clip: -
Sheath: cordura
Note: -

Charming knife used by the Japanese farmer.

As is typical for many agricultural implements, this Japanese knife is also extremely simple but the result of a centuries-old improvement that has found the difficult balance between form and function, and between cost and benefit.

The main feature is certainly the quality of the blade, in fact it uses a three-layer San Mai steel, of which the very hard one in the center.

It has a razor wire, as befits a tool created to cut and not just to be displayed in display cases.

Blade: San Mai carbon steel - Yasuki Steel Blue Paper Steel 62hrc in clad
Handle: iron foil
Closing: without blade lock
Length closed: 11mm.
Blade length: 72mm.
Blade thickness: 2.7mm
Open length: 170mm
Weight: 42g.
Note: